About the App

The app

Welcome to the all-new HUM-ID App 3.0.10! The latest release includes brand new features, an amazing easy to use interface and some major stability improvements. This animated manual guides you through the app.

New Features in V3

With the release of the latest version 3 we made it simpler than ever to create graphical sensor reports. The feature can be found under Projects / New Projects / Graphical check (Pro). During the initial check you create the sensor grid in two steps: 1. The outline sensors, 2. The inline sensors.

In addition we brought back the „classical sensor control“ – the fastest way to create a sensor project that you want to keep track of. This mode can be found under Projects / New project / Sensor control.

Keep in mind that for both project-modes the initial check is very important because you not only check the sensors for wetness but you register the sensors for the first time and link them to your project. In every following control of this project the specific sensors you read during the initial control will be searched.

 

Feedback

We are continuously improving the HUM-ID app giving our customers the best product experience possible. That is why we are dependent on our users’ feedback. We are always interested in your personal experience with the HUM-ID system.

Ihre Email-Adresse*

Ihr Feedback:


Projects

General

We completely redesigned the projects section within the app. Additional to the basic data it is now possible to link more relevant information to your project such as area of application, contextual materials, sensor grid, insulation information and much more. Those individual project data are being shown on every sensor report and are very helpful when you search for the cause of any wetness damage.

New project

Enter the project data before you start the initial check. Just tap „Manage projects“ on the app’s first screen and then hit the „New Project“ button. First enter the project name and the project address (i.e. „Car Dealership“). Those info are displayed on the project overview page and help you to navigate through your projects.

On the next four screens you can enter more project data by tapping on the select boxes. At the end, you can enter additional information (i.e. weather conditions).

Edit project

You can edit the master data of a project at any time. Navigate to „Manage projects“, choose your project and click on „View and edit project details“. Just change the data you want to change and hit the save button at the end.

Delete project

You can delete the project via the project overview page. Just choose the project of the list, swipe to the left and hit „Delete“.

Please note that you cannot recover a project and all its data once it is deleted.

Connect

Before you start

The smartphone App controls the scanner. Both devices are being connected via Bluetooth. The Bluetooth connection between the HD EXA and the smartphone will be established within the app – every time you are starting a scan.

At first please turn your HD EXA on. 

  1. Go to your smartphone settings and turn on Bluetooth.
  2. Launch the HUM-ID app on your smartphone. Go to a project you want to scan and choose the scan mode (Sensor control or Graphical check).
  3. iOS devices auto-connect to the scanner when Bluetooth is turned on. Android users choose the scanner from the Bluetooth device list actively.

It takes up to 30 seconds until the connection is being established. If you still having trouble with the connection try the following steps:

  • Quit the HUM-ID App (do NOT delete it)
  • Decouple the HD EXA in the Bluetooth settings of your smartphone. Press and hold all three buttons of the HD EXA for at least 5 seconds. You hear an acoustic signal as the HD EXA turns off..
  • Restart the HD EXA and open the HUM-ID App on your smartphone again and wait until both devices are paired.

If the HD EXA is paired to the host device, it stores information about the paired devices and tries to connect automatically when turned on. Using the “Unpair a Bluetooth device” key clears paired device from the HD EXA’s memory.

  • Make sure device is disconnected.
  • Press and keep left “Unpair” button down at least 3 second.
  • When device beeps three times, pairing is cleared. Device may reboot.

Android devices

iOS devices auto-connect to the scanner when Bluetooth is turned on. Android users choose the scanner from the Bluetooth device list actively.

Test mode

About this mode

The Test mode (formerly called Quick scan“) lets you check single sensors – independendent from any project. You can reach the test mode from the home screen. This mode is helpful if you want to check specific spots of a surface quickly or want to get familiar with HUM-ID as a concept.

The Test mode is not recommended if you want to check a project as a whole. For doing this you first have to set up a project, register the sensors individually and then perform the classical Sensor Control. If you have a lot of experience with the Classic Sensor Control, you want to try out the Graphical Check (Beta).

After you tab Test mode on the home screen you’ll see the device connect screen – learn here what you have to do to connect your smartphone to the HD EXA.

Locate wet sensors

When you scan a wet sensor, the reading process stops, the screen turns orange and the localization screens appears. The visualization shows your position in relation to the prior found wet sensor. The closer you get to the sensor the higher the percentage on the screen. To continue scanning, just tap on the screen.

Share result in Test mode


You can share the scan results of the Test mode at any time by hitting the share symbol in the upper right corner.

Sensor Control (recommended)

General

If you want to check the status of the sensors of an existing project you can choose between Sensor control (recommended) and Graphical check Beta (only advanced users).

In both cases the initial check is of particular importance, because here you do not only check if the sensors are wet or dry but you initially register each and every sensor to the project as well.

As opposed to the more complicated Graphical check in the classical Sensor control you do not have to create a optical representation of the surface you want to check. Therefor this mode is much faster and is most common used by our customers.

Please note: Even in the standard mode should read the sensors very carefully during the initial check and scan the sensors in a structured way. It is best to read and register the sensors one after another and walk in orthogonally lanes. Dependent on the initial reading order every sensor is given ascending unique sensor ID during the initial check.

The more precise you read the sensors at the initial check the easier it is to find and check the sensors on following checks.

The initial check should be created directly after the sealing is beeing finished.

Before you start

After your Smartphone is connected to the scanner and you choose „Sensor control“ you’ll see 5 hints how to procede the initial check. When you hit „Start“ the app changes to the scan mode.
Go to the starting point of the initial check – it is highly recommended to choose a prominent edge of the surface.

When you are ready hit the „Start“ button. The app changes to the scan mode and the exa searches for the first sensor near by.

Regarding the reading power:
When you first check a project the reading power is dimmed to a low level, so that you only register the sensor right in front of you – the app gives each and every single sensor an ascending ID.

If you still read too many sensors at the same time you can lower the reading power manually by tapping the settings button on the bottom right corner of the screen.

If you cannot read any sensor do the same and decrease the reading power via the same button.

Start und Stopp

You can start and stop the scan by tapping the the big round button at the bottom of the scan screen. 

Graphical check (beta)

The Graphical check (beta) enables you to to draw a map of the actual surface and the the sensors which are beeing integrated. It is a bit tricky during the initial check since you have to to define the surface edges during the initial check, but it is very helpful for upcoming checks of the same project.

We highly recommend to train the graphical check first with about 50-100 visible sensors, somewhere outside where you can see the sensors. Just start a „Test Project“ and choose „Graphical Check“ and follow the instructions. As soon as you get used to the logic of the inital check you can perform the mode with an actual HUM-ID project.

Please note

When you perform the initial check in the Graphical mode (beta) you not only draw the sensor map but you check the sensors for wetness at the same time. The initial check is devided in to phases: 1. The Outline and 2. The Filling.

Before you start

After you entered the project dertails and connected your smartphone to the scanner, you can start the inital check by hitting the „Graphical check (beta)“ button.

You see a short introduction first guiding you to the process of recording the outline. Tap „OK“ to start registering the outline sensors. You now have to register one sensor after the other which are placed at the outline of the surface.

Start and stop

If you want to pause or quit the scan of the outline, just hit the big button at the bottom of the screen.

Step 1: Defining the outline (Reading the outline sensors)

Start with a prominent edge of the surface. When the scanning mode is active you should be able to read the first sensor. Now read one outline sensor after the other and move slowly to the first edge of the surface.  Everytime you’re reaching an edge, stand still for a second an hit the arrow in which direction you’ll go next. The grid automatically turns to that direction.

 

The grid always turns 90° if you tap on one of the arrows.

Now continue the registration of the outline sensors of the next border until you reach the next edge. Go on with this procedure until you arrive at the first sensor that you have registered. The app automatically closes the outline and asks you if this outline is okay. You can discard the outline if it looks not like the actual outline at all and restart the progress again. If the ouline looks somewhat like the actual outline hit „OK“ to go on with registration of the inner sensors.

Step 2: Defining the filling (Reading the inner sensors)

As soon as you are reaching the first first outline sensor again tha apps asks you to confirm the outline. You can wether confirm it or start all over again with the outline.

When you are happy with the outline it’s time to register the inner sensors. Before you start with this you’ll see some hints of how to precede. When you are ready go to the first outline sensor, move one sensor to the right (or left) and hit the Start button.

You’ll hear a sound indicating that you are ontop of an outline sensor. Now you’ll have to go in a straight lane directly to the outline sensor on the opposite outline. Go slow and hold the scanner as intended to register the sensors in that line until you’re reaching the opposite side. You’ll here a sound that indicates that you read the already registered sensor of the grid. All the filling sensors of that lane are now visible in the graphic.

Now, you’ll have turn around and read the next outline sensor to start the second lane. After you hear the respective feedback sound you’ll start with the second lane. You move slowly to the opposite outline sensor until you’ll reach it.

Just go on in that mode until moving from outline sensor to outline sensor until all the filling sensors are registered. Hit the Start/Stop-button when you are done.

Changing the reading power

Regarding the reading power:
When you first check a project the reading power is dimmed to a low level, so that you only register the sensor right in front of you – the app gives each and every single sensor an ascending ID.

If you still read too many sensors at the same time you can lower the reading power manually by tapping the settings button on the bottom right corner of the screen.

If you cannot read any sensor do the same and decrease the reading power via the same button.

Undo

If you are registered a sensor by accident you can always use the UNDO Button on the bottom left.

This function comes in handy, when you’re reading power is too high and you read too much sensors at the same time.

Further checks

About further checks

When you are done with the initial check and the sensor grid looks the grid is beeing save. The next time you’ll open the project you can choose Manage checks > New Check.

You’ll see the gird that you initially generated. All the sensors are grey. Just start the check and go (with a default high reading power) over the surface and read the sensors. All dry sensors are turning green, all wet sensors orange.

Locating wet sensors

When you scan a wet sensor, the reading process stops, the screen turns orange and the localization screens appears. The visualization shows your position in relation to the prior found wet sensor. The closer you get to the sensor the higher the percentage on the screen. To continue scanning, just tap on the screen.

Reports

About reports

After you finish a sensor check you’re able to share the generated PDF report with colleagues or send the report to yourself. You can also save the report to your smartphone drive. Just go to Projects, choose your project, tap an Manage checks, choose the check and hit „Send report“. The sharing options are popping up.

Support Hotline

Having trouble with the app? We gladly assist you. Please call:

+49 (0)30 683 20 41 77